Preparation of glucose hydrogel as actuator in microvalve

Nur Azrina Dzulkefli, Masoomeh Tehranirokh, Burhanuddin Yeop Majlis

Research output: Chapter in Book/Report/Conference proceedingConference contribution

2 Citations (Scopus)

Abstract

This paper reports on the preparation and the swelling studies of glucose hydrogel for microvalve. This glucose hydrogel were synthesized with 80 mg Acrylamide (Aam) and crosslinked with a bifunctional crosslinking agent, 0.5 mg N,N' Methylene-Bisacrylamide (Bis). The hydrogel polymerization were initiated with 0.5 mg Ammonium Persulfate (APS) and the reaction rate is accelerated by the addition of catalyst, 5 pi N'N, N, N' Tetramethylene Diamine (TEMED). The TEMED only added when the gel is completely ready for polymerization to occur. The hydrogel microstructures were planned to fabricate by using photo resist lithography and dry etching similar done by Antonio. Et al 2004. The swelling studies will help for applying the open/close movement of cantilever, once the complete system of normally closed micro valve has been fully fabricated.

Original languageEnglish
Title of host publicationIEEE International Conference on Semiconductor Electronics, Proceedings, ICSE
Pages227-231
Number of pages5
DOIs
Publication statusPublished - 2008
Event2008 IEEE International Conference on Semiconductor Electronics, ICSE 2008 - Johor Bahru, Johor
Duration: 25 Nov 200827 Nov 2008

Other

Other2008 IEEE International Conference on Semiconductor Electronics, ICSE 2008
CityJohor Bahru, Johor
Period25/11/0827/11/08

Fingerprint

Hydrogel
Hydrogels
Glucose
Actuators
Diamines
Swelling
Polymerization
Ammonium persulfate
Dry etching
Acrylamide
Crosslinking
Lithography
Reaction rates
Gels
Microstructure
Catalysts

Keywords

  • Glucose
  • Hydrogel
  • Micro valve
  • Swelling

ASJC Scopus subject areas

  • Electrical and Electronic Engineering
  • Electronic, Optical and Magnetic Materials

Cite this

Dzulkefli, N. A., Tehranirokh, M., & Yeop Majlis, B. (2008). Preparation of glucose hydrogel as actuator in microvalve. In IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE (pp. 227-231). [4770313] https://doi.org/10.1109/SMELEC.2008.4770313

Preparation of glucose hydrogel as actuator in microvalve. / Dzulkefli, Nur Azrina; Tehranirokh, Masoomeh; Yeop Majlis, Burhanuddin.

IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE. 2008. p. 227-231 4770313.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Dzulkefli, NA, Tehranirokh, M & Yeop Majlis, B 2008, Preparation of glucose hydrogel as actuator in microvalve. in IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE., 4770313, pp. 227-231, 2008 IEEE International Conference on Semiconductor Electronics, ICSE 2008, Johor Bahru, Johor, 25/11/08. https://doi.org/10.1109/SMELEC.2008.4770313
Dzulkefli NA, Tehranirokh M, Yeop Majlis B. Preparation of glucose hydrogel as actuator in microvalve. In IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE. 2008. p. 227-231. 4770313 https://doi.org/10.1109/SMELEC.2008.4770313
Dzulkefli, Nur Azrina ; Tehranirokh, Masoomeh ; Yeop Majlis, Burhanuddin. / Preparation of glucose hydrogel as actuator in microvalve. IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE. 2008. pp. 227-231
@inproceedings{29cdd6a13af341bbbfd76e6e80992e5f,
title = "Preparation of glucose hydrogel as actuator in microvalve",
abstract = "This paper reports on the preparation and the swelling studies of glucose hydrogel for microvalve. This glucose hydrogel were synthesized with 80 mg Acrylamide (Aam) and crosslinked with a bifunctional crosslinking agent, 0.5 mg N,N' Methylene-Bisacrylamide (Bis). The hydrogel polymerization were initiated with 0.5 mg Ammonium Persulfate (APS) and the reaction rate is accelerated by the addition of catalyst, 5 pi N'N, N, N' Tetramethylene Diamine (TEMED). The TEMED only added when the gel is completely ready for polymerization to occur. The hydrogel microstructures were planned to fabricate by using photo resist lithography and dry etching similar done by Antonio. Et al 2004. The swelling studies will help for applying the open/close movement of cantilever, once the complete system of normally closed micro valve has been fully fabricated.",
keywords = "Glucose, Hydrogel, Micro valve, Swelling",
author = "Dzulkefli, {Nur Azrina} and Masoomeh Tehranirokh and {Yeop Majlis}, Burhanuddin",
year = "2008",
doi = "10.1109/SMELEC.2008.4770313",
language = "English",
isbn = "9781424425617",
pages = "227--231",
booktitle = "IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE",

}

TY - GEN

T1 - Preparation of glucose hydrogel as actuator in microvalve

AU - Dzulkefli, Nur Azrina

AU - Tehranirokh, Masoomeh

AU - Yeop Majlis, Burhanuddin

PY - 2008

Y1 - 2008

N2 - This paper reports on the preparation and the swelling studies of glucose hydrogel for microvalve. This glucose hydrogel were synthesized with 80 mg Acrylamide (Aam) and crosslinked with a bifunctional crosslinking agent, 0.5 mg N,N' Methylene-Bisacrylamide (Bis). The hydrogel polymerization were initiated with 0.5 mg Ammonium Persulfate (APS) and the reaction rate is accelerated by the addition of catalyst, 5 pi N'N, N, N' Tetramethylene Diamine (TEMED). The TEMED only added when the gel is completely ready for polymerization to occur. The hydrogel microstructures were planned to fabricate by using photo resist lithography and dry etching similar done by Antonio. Et al 2004. The swelling studies will help for applying the open/close movement of cantilever, once the complete system of normally closed micro valve has been fully fabricated.

AB - This paper reports on the preparation and the swelling studies of glucose hydrogel for microvalve. This glucose hydrogel were synthesized with 80 mg Acrylamide (Aam) and crosslinked with a bifunctional crosslinking agent, 0.5 mg N,N' Methylene-Bisacrylamide (Bis). The hydrogel polymerization were initiated with 0.5 mg Ammonium Persulfate (APS) and the reaction rate is accelerated by the addition of catalyst, 5 pi N'N, N, N' Tetramethylene Diamine (TEMED). The TEMED only added when the gel is completely ready for polymerization to occur. The hydrogel microstructures were planned to fabricate by using photo resist lithography and dry etching similar done by Antonio. Et al 2004. The swelling studies will help for applying the open/close movement of cantilever, once the complete system of normally closed micro valve has been fully fabricated.

KW - Glucose

KW - Hydrogel

KW - Micro valve

KW - Swelling

UR - http://www.scopus.com/inward/record.url?scp=65949119994&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=65949119994&partnerID=8YFLogxK

U2 - 10.1109/SMELEC.2008.4770313

DO - 10.1109/SMELEC.2008.4770313

M3 - Conference contribution

SN - 9781424425617

SP - 227

EP - 231

BT - IEEE International Conference on Semiconductor Electronics, Proceedings, ICSE

ER -