Investigation of tangential force on ball nose rake face during high-speed milling of Inconel 718

M. S. Kasim, Che Hassan Che Haron, Jaharah A Ghani, R. Izamshah, M. Akmal, M. A. Ali, M. Hadzley, M. S. Salleh

Research output: Contribution to journalArticle

1 Citation (Scopus)

Abstract

Notch wear and flaking are common tool damage found during end milling. The problems are caused by abrasive wear and excessive cyclic load exerted on cutting tool. This study presents an experimental investigation on the effect of various cutting parameters in high-speed machining of aged Inconel 718 on the tangential force. The effect of cutting speed, feed rate, depth of cut and width of cut on cutting forces had been studied. The cutting parameters were cutting speed, Vc of 100–140 m/min, feed rate, fz of 0.1–0.2 mm/tooth, depth of cut, ap of 0.5–1.0 mm and width of cut, ae of 0.2–1.8 mm. The results show that the width of cut is the main factor in controlling tangential force during end milling, followed by depth of cut and feed rate. These factors controlling the volume of material removed so that larger stress created on the cutter rake face.

Original languageEnglish
Pages (from-to)378-384
Number of pages7
JournalAdvances in Materials and Processing Technologies
Volume4
Issue number3
DOIs
Publication statusPublished - 3 Jul 2018

Fingerprint

Cyclic loads
Cutting tools
Abrasion
Machining
Wear of materials

Keywords

  • ball nose
  • end mill
  • flaking
  • high-speed milling
  • Inconel 718
  • notch wear
  • tangential forces

ASJC Scopus subject areas

  • Materials Science(all)
  • Industrial and Manufacturing Engineering
  • Mechanics of Materials

Cite this

Investigation of tangential force on ball nose rake face during high-speed milling of Inconel 718. / Kasim, M. S.; Che Haron, Che Hassan; A Ghani, Jaharah; Izamshah, R.; Akmal, M.; Ali, M. A.; Hadzley, M.; Salleh, M. S.

In: Advances in Materials and Processing Technologies, Vol. 4, No. 3, 03.07.2018, p. 378-384.

Research output: Contribution to journalArticle

Kasim, M. S. ; Che Haron, Che Hassan ; A Ghani, Jaharah ; Izamshah, R. ; Akmal, M. ; Ali, M. A. ; Hadzley, M. ; Salleh, M. S. / Investigation of tangential force on ball nose rake face during high-speed milling of Inconel 718. In: Advances in Materials and Processing Technologies. 2018 ; Vol. 4, No. 3. pp. 378-384.
@article{3c408f59df87405989e58433a18ca657,
title = "Investigation of tangential force on ball nose rake face during high-speed milling of Inconel 718",
abstract = "Notch wear and flaking are common tool damage found during end milling. The problems are caused by abrasive wear and excessive cyclic load exerted on cutting tool. This study presents an experimental investigation on the effect of various cutting parameters in high-speed machining of aged Inconel 718 on the tangential force. The effect of cutting speed, feed rate, depth of cut and width of cut on cutting forces had been studied. The cutting parameters were cutting speed, Vc of 100–140 m/min, feed rate, fz of 0.1–0.2 mm/tooth, depth of cut, ap of 0.5–1.0 mm and width of cut, ae of 0.2–1.8 mm. The results show that the width of cut is the main factor in controlling tangential force during end milling, followed by depth of cut and feed rate. These factors controlling the volume of material removed so that larger stress created on the cutter rake face.",
keywords = "ball nose, end mill, flaking, high-speed milling, Inconel 718, notch wear, tangential forces",
author = "Kasim, {M. S.} and {Che Haron}, {Che Hassan} and {A Ghani}, Jaharah and R. Izamshah and M. Akmal and Ali, {M. A.} and M. Hadzley and Salleh, {M. S.}",
year = "2018",
month = "7",
day = "3",
doi = "10.1080/2374068X.2018.1451031",
language = "English",
volume = "4",
pages = "378--384",
journal = "Advances in Materials and Processing Technologies",
issn = "2374-068X",
publisher = "Taylor and Francis Ltd.",
number = "3",

}

TY - JOUR

T1 - Investigation of tangential force on ball nose rake face during high-speed milling of Inconel 718

AU - Kasim, M. S.

AU - Che Haron, Che Hassan

AU - A Ghani, Jaharah

AU - Izamshah, R.

AU - Akmal, M.

AU - Ali, M. A.

AU - Hadzley, M.

AU - Salleh, M. S.

PY - 2018/7/3

Y1 - 2018/7/3

N2 - Notch wear and flaking are common tool damage found during end milling. The problems are caused by abrasive wear and excessive cyclic load exerted on cutting tool. This study presents an experimental investigation on the effect of various cutting parameters in high-speed machining of aged Inconel 718 on the tangential force. The effect of cutting speed, feed rate, depth of cut and width of cut on cutting forces had been studied. The cutting parameters were cutting speed, Vc of 100–140 m/min, feed rate, fz of 0.1–0.2 mm/tooth, depth of cut, ap of 0.5–1.0 mm and width of cut, ae of 0.2–1.8 mm. The results show that the width of cut is the main factor in controlling tangential force during end milling, followed by depth of cut and feed rate. These factors controlling the volume of material removed so that larger stress created on the cutter rake face.

AB - Notch wear and flaking are common tool damage found during end milling. The problems are caused by abrasive wear and excessive cyclic load exerted on cutting tool. This study presents an experimental investigation on the effect of various cutting parameters in high-speed machining of aged Inconel 718 on the tangential force. The effect of cutting speed, feed rate, depth of cut and width of cut on cutting forces had been studied. The cutting parameters were cutting speed, Vc of 100–140 m/min, feed rate, fz of 0.1–0.2 mm/tooth, depth of cut, ap of 0.5–1.0 mm and width of cut, ae of 0.2–1.8 mm. The results show that the width of cut is the main factor in controlling tangential force during end milling, followed by depth of cut and feed rate. These factors controlling the volume of material removed so that larger stress created on the cutter rake face.

KW - ball nose

KW - end mill

KW - flaking

KW - high-speed milling

KW - Inconel 718

KW - notch wear

KW - tangential forces

UR - http://www.scopus.com/inward/record.url?scp=85059146356&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85059146356&partnerID=8YFLogxK

U2 - 10.1080/2374068X.2018.1451031

DO - 10.1080/2374068X.2018.1451031

M3 - Article

AN - SCOPUS:85059146356

VL - 4

SP - 378

EP - 384

JO - Advances in Materials and Processing Technologies

JF - Advances in Materials and Processing Technologies

SN - 2374-068X

IS - 3

ER -