Characterizing deformation behaviour of an oxidized high speed steel

Effects of nanoindentation depth, friction and oxide scale porosity

G. Y. Deng, A. K. Tieu, L. H. Su, H. T. Zhu, Q. Zhu, Wan Fathul Hakim W. Zamri, C. Kong

Research output: Contribution to journalArticle

1 Citation (Scopus)

Abstract

In the present paper, a systematic study on the deformation behaviour of an oxidized high speed steel (HSS) during nanoindentation has been conducted. Specimens cut from a HSS work roll were oxidized first to develop the oxide layer with thickness close to that built up on a HSS work roll surface during hot rolling in industry. Then, nanoindentation tests with three typical peak loads from low to high (namely 2 mN, 20 mN, and 200 mN) were conducted on the oxide scale surface. Porosity in oxide scale and its surface morphology features were examined by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. In addition, a finite element model was developed and verified by comparing with the experimental measured load-depth curves. With the developed model, for the first time, a systematic investigation has been done to understand the effects of nanoindentation depth (from 10 nm to 1250 nm), friction coefficient (from 0 to 0.6) and initial porosity of oxide scale (from 0 to 20%) during nanoindentation on the deformation behaviours of both oxide scale and HSS substrate. It has been found an obvious size effect and three regions can be divided according to nanoindentation depth, based on the evolution of mechanical property, porosity in oxide scale, and plastic deformations in both oxide scale and HSS substrate. This study also revealed that friction has a slight influence during nanoindentation and almost the same results were obtained when the friction coefficient is larger than 0.3. By contrast, a large influence of porosity in oxide scale was observed.

Original languageEnglish
Pages (from-to)267-285
Number of pages19
JournalInternational Journal of Mechanical Sciences
Volume155
DOIs
Publication statusPublished - 1 May 2019

Fingerprint

Steel
Nanoindentation
nanoindentation
Oxides
friction
Porosity
high speed
steels
Friction
porosity
oxides
coefficient of friction
hot surfaces
Hot rolling
Substrates
plastic deformation
Surface morphology
Plastic deformation
industries
mechanical properties

Keywords

  • Friction
  • High speed steel
  • Hot rolling
  • Nanoindentation
  • Oxide scale
  • Porosity

ASJC Scopus subject areas

  • Civil and Structural Engineering
  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

Cite this

Characterizing deformation behaviour of an oxidized high speed steel : Effects of nanoindentation depth, friction and oxide scale porosity. / Deng, G. Y.; Tieu, A. K.; Su, L. H.; Zhu, H. T.; Zhu, Q.; W. Zamri, Wan Fathul Hakim; Kong, C.

In: International Journal of Mechanical Sciences, Vol. 155, 01.05.2019, p. 267-285.

Research output: Contribution to journalArticle

@article{e7b5cd04018543979928e4a894d00d6a,
title = "Characterizing deformation behaviour of an oxidized high speed steel: Effects of nanoindentation depth, friction and oxide scale porosity",
abstract = "In the present paper, a systematic study on the deformation behaviour of an oxidized high speed steel (HSS) during nanoindentation has been conducted. Specimens cut from a HSS work roll were oxidized first to develop the oxide layer with thickness close to that built up on a HSS work roll surface during hot rolling in industry. Then, nanoindentation tests with three typical peak loads from low to high (namely 2 mN, 20 mN, and 200 mN) were conducted on the oxide scale surface. Porosity in oxide scale and its surface morphology features were examined by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. In addition, a finite element model was developed and verified by comparing with the experimental measured load-depth curves. With the developed model, for the first time, a systematic investigation has been done to understand the effects of nanoindentation depth (from 10 nm to 1250 nm), friction coefficient (from 0 to 0.6) and initial porosity of oxide scale (from 0 to 20{\%}) during nanoindentation on the deformation behaviours of both oxide scale and HSS substrate. It has been found an obvious size effect and three regions can be divided according to nanoindentation depth, based on the evolution of mechanical property, porosity in oxide scale, and plastic deformations in both oxide scale and HSS substrate. This study also revealed that friction has a slight influence during nanoindentation and almost the same results were obtained when the friction coefficient is larger than 0.3. By contrast, a large influence of porosity in oxide scale was observed.",
keywords = "Friction, High speed steel, Hot rolling, Nanoindentation, Oxide scale, Porosity",
author = "Deng, {G. Y.} and Tieu, {A. K.} and Su, {L. H.} and Zhu, {H. T.} and Q. Zhu and {W. Zamri}, {Wan Fathul Hakim} and C. Kong",
year = "2019",
month = "5",
day = "1",
doi = "10.1016/j.ijmecsci.2019.02.043",
language = "English",
volume = "155",
pages = "267--285",
journal = "International Journal of Mechanical Sciences",
issn = "0020-7403",
publisher = "Elsevier Limited",

}

TY - JOUR

T1 - Characterizing deformation behaviour of an oxidized high speed steel

T2 - Effects of nanoindentation depth, friction and oxide scale porosity

AU - Deng, G. Y.

AU - Tieu, A. K.

AU - Su, L. H.

AU - Zhu, H. T.

AU - Zhu, Q.

AU - W. Zamri, Wan Fathul Hakim

AU - Kong, C.

PY - 2019/5/1

Y1 - 2019/5/1

N2 - In the present paper, a systematic study on the deformation behaviour of an oxidized high speed steel (HSS) during nanoindentation has been conducted. Specimens cut from a HSS work roll were oxidized first to develop the oxide layer with thickness close to that built up on a HSS work roll surface during hot rolling in industry. Then, nanoindentation tests with three typical peak loads from low to high (namely 2 mN, 20 mN, and 200 mN) were conducted on the oxide scale surface. Porosity in oxide scale and its surface morphology features were examined by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. In addition, a finite element model was developed and verified by comparing with the experimental measured load-depth curves. With the developed model, for the first time, a systematic investigation has been done to understand the effects of nanoindentation depth (from 10 nm to 1250 nm), friction coefficient (from 0 to 0.6) and initial porosity of oxide scale (from 0 to 20%) during nanoindentation on the deformation behaviours of both oxide scale and HSS substrate. It has been found an obvious size effect and three regions can be divided according to nanoindentation depth, based on the evolution of mechanical property, porosity in oxide scale, and plastic deformations in both oxide scale and HSS substrate. This study also revealed that friction has a slight influence during nanoindentation and almost the same results were obtained when the friction coefficient is larger than 0.3. By contrast, a large influence of porosity in oxide scale was observed.

AB - In the present paper, a systematic study on the deformation behaviour of an oxidized high speed steel (HSS) during nanoindentation has been conducted. Specimens cut from a HSS work roll were oxidized first to develop the oxide layer with thickness close to that built up on a HSS work roll surface during hot rolling in industry. Then, nanoindentation tests with three typical peak loads from low to high (namely 2 mN, 20 mN, and 200 mN) were conducted on the oxide scale surface. Porosity in oxide scale and its surface morphology features were examined by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. In addition, a finite element model was developed and verified by comparing with the experimental measured load-depth curves. With the developed model, for the first time, a systematic investigation has been done to understand the effects of nanoindentation depth (from 10 nm to 1250 nm), friction coefficient (from 0 to 0.6) and initial porosity of oxide scale (from 0 to 20%) during nanoindentation on the deformation behaviours of both oxide scale and HSS substrate. It has been found an obvious size effect and three regions can be divided according to nanoindentation depth, based on the evolution of mechanical property, porosity in oxide scale, and plastic deformations in both oxide scale and HSS substrate. This study also revealed that friction has a slight influence during nanoindentation and almost the same results were obtained when the friction coefficient is larger than 0.3. By contrast, a large influence of porosity in oxide scale was observed.

KW - Friction

KW - High speed steel

KW - Hot rolling

KW - Nanoindentation

KW - Oxide scale

KW - Porosity

UR - http://www.scopus.com/inward/record.url?scp=85062591241&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85062591241&partnerID=8YFLogxK

U2 - 10.1016/j.ijmecsci.2019.02.043

DO - 10.1016/j.ijmecsci.2019.02.043

M3 - Article

VL - 155

SP - 267

EP - 285

JO - International Journal of Mechanical Sciences

JF - International Journal of Mechanical Sciences

SN - 0020-7403

ER -